[Top] [Prev] [Next] [Bottom]

Appendix C

Router Worksheets

This appendix contains the following worksheets to help you in your initial configuration of the router portion of your 3000 Series D Secure Gateway Router. Use the worksheet(s) appropriate for your configuration.

IP Addressing

Dialup PPP

Frame Relay

ISDN

IP Addressing

You need the following IP addressing information for all 3000 Series D gateway routers.

What is the IP address for your 3000 Series D Ethernet interface?

This address must be unique on the Ethernet.
______.______.______.______

What is the IP subnet mask for your 3000 Series D Ethernet interface?
______.______.______.______

What are the IP addresses and subnet masks of the WAN interfaces?

In place of an assigned IP address, you can use unnumbered IP or dynamic IP addressing.

In the command line interface, to set up
IP Address ____.____.____.___
Mask____.____.____.____

IP Address ____.____.____.___
Mask ____.____.____.____

IP Address ____.____.____.___
Mask____.____.____.____

IP Address ____.____.____.___
Mask ____.____.____.____

I am using (choose at least one)

Notes:

(a) _____ RIP

(b) _____ Default gateway of
_____._____._____._____

(c) _____ Static route to
____.____.____.____

Address mask
____.____.____.____

Via gateway
____.____.____.____

Number of hops to gateway
_____

(d) _____ OSPF
Area ____.____.____.____
Authentication Type ____
(1 = a password; 0 = none)
Stub Area ____ Yes ____ No

IP Addressing, continued

Dialup PPP

You need the following information to set up your 3000 Series D for dialup PPP.

My modem is

(The manual for your modem specifies this. Most popular retail modems are asynchronous.)

_____ Asynchronous

_____ Synchronous

The name for my modem is

Assign a unique name to your modem.

(You can use the manufacturer's name.)

_________________________

The initialization string for my modem is

(Since there are many brands of modems, each with its own idiosyncrasies, you must configure each modem that you add. Your 3000 Series D has default settings, which are adequate for most situations.)

_________________________

Destination name is

The telephone number of the destination is

_________________________

_________________________

For authentication, I am using

_____ PAP _____ CHAP

_____ Login sequence

If using PAP, password is

_________________________

If using CHAP, secret is

_________________________

Allow incoming calls?

_____ Yes _____ No

Dial-on-demand

_____ Yes _____ No

If yes, idle timeout: ___ seconds

Frame Relay

Your Frame Relay service provider gives you the information you need to set up your 3000 Series D for Frame Relay.

For configurations where you are running IPX or bridging over Frame Relay or using multiple Permanent Virtual Circuits (PVCs), Nx Networks recommends that you read the Frame Relay documentation in the Online Library available on the Nx Networks Web site at www.nxnetworks.com or on the CD that comes with your 3000 Series D.

What type of Local Management Interface (LMI) does your Frame Relay switch use?

The 3000 Series D supports REV1, ANSI, and CCITT. The default is ANSI. Most providers use REV1 or ANSI.


_____________

Use Frame Relay LAN Emulation (FRLANE)?

Nx Networks recommends that you answer No to this question and instead use Frame Relay Virtual Circuit (FRVC) unless you are using more than one PVC. If you use FRLANE, refer to the documentation mentioned above.

_____ Yes _____ No

Circuit Name (1-23 characters)

_______________________

Frame Relay, continued

Note: The following information must match the configuration of the Frame Relay switch to which your 3000 Series D is connected.

Circuit Number (16-1007)

________

Committed Information Rate (CIR) in bps (300 to 2048000). Default is 64000.


_______________ bps

Committed Burst Size (Bc) in bits (300 to 2048000). Default is 64000.

_______________ bps

Excess Burst Size (Be) (0 to 2048000).
Default is 0.


_______________ bps

Frame Relay access rate (internal clock speed) (4800 to 2048000). Default is 2048000.


_______________ bps

ISDN

You need the following information to set up your 3000 Series D for ISDN. Your ISDN provider gives you this information (except for the destination telephone numbers).

Telephone number(s) of your 3000 Series D ISDN interface. (A single interface can have multiple numbers.)

_________________________

_________________________

_________________________

_________________________

Destination names and telephone numbers. (A destination interface can have multiple numbers.)

Name

Number

_________________________

_________________________

Name

Number

_________________________

_________________________

Name

Number

_________________________

_________________________

Name

Number

_________________________

_________________________

Type of ISDN switch variant

____________________

ISDN, continued

Terminal Endpoint Identifier (TEI) assigned by your ISDN provider

Note: For some North American switches, the service provider may assign a TEI for each B channel.

B1 _____________________

B2 _____________________

Service Profile IDs (SPIDs)

Note: SPIDs are used only in North America. Some switches have one SPID; others have two. SPIDs are independent of the number of B channels used.

B1 _____________________

B2 _____________________

Configured for point-to-point or multipoint?

 ____ PP

____ MP


[Top] [Prev] [Next] [Bottom]

Copyright © 2001, Nx Networks All rights reserved.