Note: Each release number (rel#) is unique. Before entering the pkgadd command, view the directory structure and determine the software package's release number. If the package has more than one release, use the highest number.

5. During installation, several messages display. Answer y if any of the following questions appear, even if asked to overwrite older files.

Do you want to install these as setuid/setgid files? [y,n,?,q] 
Do you want to continue with the installation of <package_name>? [y,n,?] 
Do you want to install these conflicting files? [y,n,?,q]

When the software has completely loaded, the following message displays.

Installation of NETRIXnoa was successful.

6. Enter the following command to load the documentation into the default directory (/opt/NETRIX).

pkgadd -d doc/rel# NETRIXdoc

7. During installation, several messages display. Answer y if any of the following questions appear, even if asked to overwrite older files:

Do you want to install these as setuid/setgid files? [y,n,?,q] 
Do you want to continue with the installation of <package_name>? [y,n,?] 
Do you want to install these conflicting files? [y,n,?,q]

When the software has completely loaded, the following message displays:

Installation of NETRIXdoc was successful.

8. To remove the CD after installing software packages, enter cd / and, at the next prompt, type eject.

Loading Software on a PC

: 1. Insert the CD into the CD-ROM drive. Auto-play should activate the installation package. If not, double-click setup.exe in the root directory of the CD.
: 2. Once the Welcome screen appears, click Next.
: 3. Enter your NetrixView 2000 node number, which is number 1.

CAUTION:
If you are updating a NetrixView 2000 installed on your PC, select the same node number and data directory used previously. Otherwise, you may lose the node's existing database.

4. Select the destination drive and directory where you want to place the NetrixView 2000 installation software.

5. Select the destination drive and directory where you want to place the NetrixView 2000 data.

Note: The software installation directory and the data directory must be on the same drive.

6. Select one of the following installation types:

Typical—installs NetrixView 2000 software, and, if not already installed on the system, Winsock2.

Full—installs NetrixView2000 software and documentation, Adobe Acrobat Reader, and, if not already installed on the system, Winsock2.

Custom—allows you to specify which software packages to install (listed above under Full).

7. Select a program folder for the NetrixView 2000 icon.

8. If the node number you entered in step 3 already exists, the prompt asks if you want to overwrite the old directory and install a new boot database. Select NO (recommended) to preserve the existing database or YES to overwrite it.

CAUTION:
If you select YES, you will lose your configuration information, and the newly installed NetrixView 2000 will automatically run in boot mode in a later step in this installation. See the NetrixView 2000 Installation Guide for further instructions.

9. If you elected to install Adobe Acrobat, respond to the screens asking questions, such as where to install the program.

10. If this is an . . .

initial installation of the NetrixView 2000 software, or if you chose to write over the previous database, the installation script automatically launches in boot mode. When the NetrixView 2000 Verification screen appears, click OK and then follow the steps in Creating the Initial Virtual Network on page 8.
update installation, on the resulting Setup Complete screen, select Restart automatically now, then click Finish.

Setting Up the Network Management System
Software on a Sun Workstation

CAUTION:
Perform these steps only for the initial installation of the network management system.

1. Open a CDE window; make sure you are not logged in as root.

2. Start the Application Manager by typing netrix at the prompt.

3. Specify a node number (usually 1-8) in the xxx Node Number field. The node number must be unique within your system. The first and/or only network management system is usually "Node 1." Press OK.

A screen shows the release installed, the node number, and a message stating that the component defaults were installed.

4. Press the Install button.

Creating the Initial Virtual Network

The first time you access a new NetrixView 2000, you enter it in boot mode to create the initial virtual network.

CAUTION:
Perform this process only once, and only as part of the initial installation of the NetrixView 2000. Do not log out until you complete the entire procedure.