Using the DVMRP Protocol

Table 1 DVMRP Commands
Command	Function
Dump Routing Tables [C]	Displays the OSPF routes contained in the routing table.
DVMRP [C]	Enables or disables DVMRP.
Exit [C] [M]	Returns to the previous prompt.
IGMP [C] [M]	Displays the IGMP configuration or monitoring prompt.
Interface Summary [M]	Displays OSPF interface statistics and parameters.
List [M]	Displays the current DVMRP configuration.
Mcache [M]	Displays a list of currently active multicast forwarding cache entries.
MOSPF [C]	Sets the metric and threshold for the DVMRP interface running over MOSPF. This command also disables the MOSPF VIF.
Mstat [M]	Displays various multicast routing statistics.
Phyint [C]	Sets the metric and threshold for LAN interfaces associated with DVMRP. This command also deletes LAN interfaces associated with DVMRP
Tunnel [C]	Adds or deletes tunnels in a MOSPF/DVMRP configuration.

Dump Routing Tables [C]

Displays the set of known DVMRP multicast sources. Each source is listed together with the DVMRP router it was learned from, an associated cost, and the number of seconds since the routing table entry was refreshed.

Syntax: dump

Example: dump

Multicast Routing Table
Type Origin-Subnet From-Gateway Metric Age In Out-Vifs
DVMRP 1.0.0.0 199.94.207.10 9 45 0 1*
DVMRP 4.0.0.0 199.94.207.10 7 45 0 1*
DVMRP 9.0.0.0 199.94.207.10 10 45 0 1*

Group:224.0.1.12 Prune sent lifetime: 0 Graft send in progress:
Group:224.0.1.11 Prune sent lifetime: 0 Graft send in progress:
Group:224.2.100.102 Prune sent lifetime: 4925 Graft send in progress:
Group:224.2.100.100 Prune sent lifetime: 4920 Graft send in progress:


Type	Type of multicast sources (DVMRP)
Origin-Subnet	IP address of the originating subnet.
From-Gateway	IP address of the gateway from which the entry came.
Metric	Associated cost of that route.
Age	Age of routing table entry as the number of seconds since the routing table entry was refreshed.
In	DVMRP VIF that multicast datagram from the source must be received on.
Out-Vifs	VIF that sends the multicast datagrams. VIFs marked with an asterisk indicate that a datagram is only forwarded if there are group members on the attached network.

DVMRP [C]

Enables or disables DVMRP on the router.

Syntax: dvmrp

on
off

on

Enables DVMRP. Enabling DVMRP automatically assigns DVMRP to all LAN interfaces that are not running MOSPF.

Example: dvmrp on

off

Disables DVMRP on the router.

Example: dvmrp off

Exit [C] [M]

Returns to the previous prompt level.

Syntax: exit

Example: exit

IGMP [C] [M]

Displays the IGMP configuration or monitoring prompt. For information on the commands available at these prompts, see IGMP Commands.

Syntax: igmp

Example: igmp

Internet Group Management Protocol Configuration
IGMP Config>

Interface Summary [M]

Displays current list of DVMRP interfaces (or VIFs).

Syntax: interface interface-ip-address

Example: interface

Virtual Interface Table
Vif Local-Address Metric Thresh Flags
0 10.1.153.22 subnet: 10.1.153.0 1 1 querier
1 10.1.154.22 subnet: 10.1.154.0 1 1 down


Vif	Number assigned to DVMRP interfaces (or VIFs) command. Each VIF is assigned a number, which is used to identify the VIF in other commands
Local Address	Local IP address of the DVMRP interface.
Metric	The metric configured on this interface
Threshold	The threshold configured on this interface
Flags	Displays whether the VIF is down or that the router is the querier (sender of IGMP Host Membership Queries) on the interface.

List [M]

Displays the current DVMRP state (on or off), tunnel configuration information, and MOSPF configuration information.

Syntax: list

Example: list

DVMRP on
tunnel 192.190.7.2 192.52.71.21 1 32
MOSPF 1 1

Mcache [M]

Displays a list of currently active multicast cache entries. Multicast cache entries are built on demand, whenever the first matching multicast datagram is received. There is a separate cache entry (and therefore a separate route) for each datagram source network and destination group combination.

Cache entries are cleared on topology changes (for example, a point-to-point line in the MOSPF system going up or down), and on group membership changes.

Note: The numbers displayed in the legend at the top of the output do NOT refer directly to VIFs, but instead refer to physical interfaces (which may be running either DVMRP or MOSPF) and tunnels. Syntax: mcache

Example: mcache

0: Eth/0 1: TKR/0 2: Internal
3: SL/0 4: 192.35.82.97

Source Destination Count Upst Downstream
128.185.146.0 239.0.0.1 1 0 2,4
128.119.0.0 224.2.199.198 9 4 3
128.9.160.0 224.2.127.255 1 4 3
13.2.116.0 224.2.0.1 27 4 3
140.173.8.0 224.2.0.1 31 4 3
128.165.114.0 224.2.0.1 25 4 3
132.160.3.0 224.2.158.99 11 4 3
132.160.3.0 224.2.170.143 56 4 3
131.188.34.0 224.2.0.1 28 4 3
131.188.34.0 224.2.199.198 28 4 3


Source	Source network/subnet of matching datagrams.
Destination	Destination group of matching datagrams.
Count	Number of entries processed for that multicast group.
Upstream	Neighboring network/router from which the datagram must be received in order to be forwarded. When this is "none," the datagram is never forwarded.
Downstream	Downstream interfaces/neighbors to which the datagram is forwarded. When this is 0, the datagram is not forwarded.

There is more information in a multicast forwarding cache entry. You can display a cache entry in detail by providing the source and destination of a matching datagram on the command line. If a matching cache entry is not found, one is built. A sample of this command is shown below:

Example: mcache 128.185.182.9 224.0.1.2

source Net: 128.185.182.0
Destination: 224.0.1.2
Use Count: 472
Upstream Type: Transit Net
Upstream ID: 128.185.184.114
Downstream: 128.185.177.11 (TTL = 2)

In addition to the information shown in the short form of the mcache command, the following fields are displayed:


Upstream Type	The type of node from which the datagram must be received to be forwarded. Possible values are none The datagram is not forwarded. router The datagram must be received over a point-to-point connection. transit network, stub network, or external the datagram is expected to be received from another Autonomous System.
Downstream	Prints a separate line for each interface or neighbor to which the datagram is sent. A TTL value is also given, indicating that datagrams forwarded out of or to this interface must have at least the specified TTL value in their IP header. When the router is itself a member of the multicast group, a line specifying internal Application appears as one of the downstream interfaces/neighbors.

MOSPF [C]

Sets the metric and threshold for the DVMRP interface running over MOSPF or disables the MOSPF VIF.

Syntax: mospf

metric threshold
delete

metric threshold

Sets the metric and threshold for the MOSPF VIF. Default values for the metric and threshold parameters are 1.

When using a MOSPF domain to join DVMRP tunnels, DVMRP actually runs over MOSPF. When this occurs a DVMRP interface named "MOSPF VIF" (VIF or virtual interface) is automatically created. DVMRP tries to run over MOSPF automatically using the MOSPF VIF.

Example: mospf 1 1

delete

Disables the MOSPF VIF. When MOSPF is enabled, DVMRP tries to run over MOSPF automatically using the MOSPF VIF.

Example: mospf delete

Mstat [M]

Displays various multicast routing statistics. The command indicates whether multicast routing is enabled and whether the router is an inter-area and/or inter-AS multicast forwarder.

Syntax: mstats

Example: mstats

MOSPF forwarding: Enabled
Inter-area forwarding: Enabled
DVMRP forwarding: Enabled

Datagrams received: 164612 Datagrams (ext source): 0
Datagrams fwd (multicast):98807 Datagrams fwd (unicast): 0
Locally delivered: 0 No matching rcv interface: 0
Unreachable source: 0 Unallocated cache entries: 0
Off multicast tree: 77230 Unexpected DL multicast: 0
Buffer alloc failure: 0 TTL scoping: 0

# DVMRP routing entries: 1808 # DVMRP entries freed: 44
# fwd cache alloc: 25659 # fwd cache freed: 25574
# fwd cache GC: 0 # local group DB alloc: 1
# local group DB free: 0


MOSPF forwarding	Displays whether the router forwards IP multicast datagrams.
Inter-area multicast	Displays whether the router forwards IP multicast datagrams between areas.
DVMRP multicast	Displays whether the router forwards IP multicast datagrams between DVMRP enabled router interfaces.
Datagrams received	Multicast datagrams received (datagrams whose destination group lies in the range 224.0.0.1 - 224.0.0.255 are not included in this total).
Datagrams (ext source)	Datagrams received whose source is outside the AS.
Datagrams fwd (multicast)	Datagrams that have been forwarded as data-link multicasts (this includes packet replications, when necessary, so this count could be greater than the number received).
Datagrams fwd (unicast)	Datagrams forwarded as data-link unicasts.
Locally delivered	Datagrams forwarded to internal applications.
No matching rcv interface	Datagrams received by a non-inter-AS multicast forwarder on a non-MOSPF interface.
Unreachable source	Datagrams whose source address was unreachable.
Unallocated cache entries	Datagrams whose cache entries could not be created due to resource shortages.
Off multicast tree	Datagrams that were not forwarded either because there was no upstream neighbor or no downstream interfaces/neighbors in the matching cache entry.
Unexpected DL multicast	Datagrams received as data-link multicasts on interfaces configured for data-link unicast.
Buffer alloc failure	Datagrams that could not be replicated because of buffer shortages.
TTL scoping	Datagrams not forwarded because their TTL indicated that they could never reach a group member.
# fwd cache alloc	Cache entries allocated. The current forwarding cache size is the number of entries allocated ("# fwd cache alloc") minus the number of cache entries freed ("# fwd cache freed").
# fwd cache freed	Cache entries freed. The current forwarding cache size is the number of entries allocated ("# fwd cache alloc") minus the number of cache entries freed ("# fwd cache freed").
# fwd cache GC	Cache entries were cleared because they were not recently used and the cache overflowed.
# local group DB alloc	Local group database entries allocated. The number allocated ("# local group DB alloc") minus the number freed ("# local group DB free") equals the current size of the local group database.
# local group DB free	Local group database entries freed. The number allocated ("# local group DB alloc") minus the number freed ("# local group DB free") equals the current size of the local group database.

The number of cache hits can be calculated as the number of datagrams received ("Datagrams received") minus the total of datagrams discarded due to "No matching rcv interface," "Unreachable source" and "Unallocated cache entries," and minus "# local group DB alloc." The number of cache misses is "# local group DB alloc."+

Phyint [C]

Sets the metric and threshold for LAN interfaces associated with DVMRP. This command also deletes LAN interfaces associated with DVMRP.

Syntax: phyint

interface address metric threshold
interface address delete

Sets the metric and threshold for LAN interfaces associated with DVMRP. Default values for the metric and threshold parameters are 1. This example shows how to add default metric and thresholds to an interface.

Example: phyint 128.185.251.1

This example shows how to set a metric and threshold that is different from the default.

Example: phyint 128.185.251.1 5 8

This example shows how to delete metric and threshold settings for an interface.

Example: phyint 128.185.251.1 delete

Tunnel [C]

Adds tunnels or deletes tunnels in a MOSPF/DVMRP configuration.

Syntax: tunnel

source-adr destination-addr metric threshold
source-addr destination-addr delete

When you add a tunnel, the metric and threshold default to 1 unless you specify a different metric or threshold. This example shows how to add a tunnel using the default metric and threshold.

Example: tunnel

Tunnel source [0.0.0.0]? 133.1.129.10
Tunnel destination [0.0.0.0]? 133.1.165.10

This example shows how to add a tunnel that has a metric and threshold other than the default. Enter the metric and threshold after the tunnel destination address.

Example: tunnel

Tunnel source [0.0.0.0]? 133.1.129.10
Tunnel destination [0.0.0.0]? 133.1.165.10 1 32

This example shows how to delete a tunnel. Enter delete after the tunnel destination address. Note that to delete a tunnel, you must enter the entire command on one line.

Example: tunnel

Tunnel source [0.0.0.0]? 133.1.129.10 133.1.165.10 delete

docs@openroute.com