ELS Messages for Ethernet Network Interface (ETH)
- Level:
- P-TRACE
- Short Syntax:
- ETH.001 brd rcv unkwn typ packet_type
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.001 broadcast packet received with unknown Ethernet type packet_type
from host source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- A broadcast packet was received with an unknown or unsupported
Ethernet type field.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.002 rcv unkwn typ packet_type
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.002 packet received with unknown Ethernet type field packet_type
from source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- A non-broadcast packet was received with an unknown or unsupported
Ethernet type field.
- Level:
- P-TRACE
- Short Syntax:
- ETH.003 brd 802.3 bd ln actual_length
claimed_length
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.003 broadcast packet received with a bad 802.3 length field actual actual_length
claimed claimed_length
from source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- A broadcast packet was received with a type field that indicated 802.3
but was shorter than data length claimed in the 802.3 header.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.004 802.3 bd ln actual_length
claimed_length
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.004 packet received with a bad 802.3 length field actual actual_length
claimed claimed_length
from source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- A non-broadcast packet was received with a type field that indicated
802.3 but was shorter than data length claimed in the 802.3 header.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.005 DN bd ln actual_length
claimed_length
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.005 DECnet packet received with a bad length actual actual_length
claimed claimed_length
from source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- A DECnet packet was received with a length field that was larger than
the actual length of the packet.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.006 IPX bd ECONFIG 8137 nd address
nt network
- Long Syntax:
- ETH.006 IPX bad ECONFIG should be 8137 node address
network network
- Description:
- An IPX packet was received with the wrong ECONFIG.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.007 IPX bd ECONFIG 802.2 nd address
nt network
- Long Syntax:
- ETH.007 IPX wrong ECONFIG should be 802.2 node address
network network
- Description:
- An IPX packet was received with the wrong ECONFIG.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.008 IL selftest_phase
fld error_condition
nt network
- Long Syntax:
- ETH.008 Interlan selftest_phase
failed: error_condition
, network network
- Description:
- The selftest for the Interlan Ethernet card has reported an error
during selftest.
- Cause:
- Generally this indicates a hardware error with the card.
- Action:
- Refer to the router hardware manual and the Ethernet card manual
for more details.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.009 PE selftest_phase
fld error_condition
nt network
- Long Syntax:
- ETH.009 Ethernet selftest_phase
failed: error_condition
, network network
- Description:
- The selftest for the Ethernet card has reported an error
during selftest.
- Cause:
- Generally this indicates a hardware error with the card.
- Action:
- Refer to the router hardware manual for more details.
- Level:
- C-INFO
- Short Syntax:
- ETH.010 LLC unk SAP DSAP
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.010 802.2 LLC packet received with unknown DSAP DSAP
from host source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- An 802.2 LLC packet was received from the network with an inactive
(unrecognized) DSAP.
- Level:
- C-INFO
- Short Syntax:
- ETH.011 LLC nt typ 1 LLC_control_type
nt network
- Long Syntax:
- ETH.011 802.2 LLC packet received, not Type 1 LLC_control_type
network network
- Description:
- A packet was received from the network that had an LLC but was not a
Type 1 LLC.
- Level:
- C-INFO
- Short Syntax:
- ETH.012 LLC RSP LLC_SSAP
nt network
- Long Syntax:
- ETH.012 LLC RESPONSE packet received LLC_SSAP
network network
- Description:
- An LLC response was received from the network.
- Level:
- C-INFO
- Short Syntax:
- ETH.013 LLC XID LLC_SSAP
nt network
- Long Syntax:
- ETH.013 LLC XID packet received LLC_SSAP
network network
- Description:
- An LLC XID packet was received from the network.
- Level:
- C-INFO
- Short Syntax:
- ETH.014 LLC TEST LLC_SSAP
nt network
- Long Syntax:
- ETH.014 LLC TEST packet received LLC_SSAP
network network
- Description:
- An LLC TEST packet was received from the network.
- Level:
- U-INFO
- Short Syntax:
- ETH.015 unrec ctl LLC_control_field
nt network
- Long Syntax:
- ETH.015 packet received with unrecognized control field LLC_control_field
network network
- Description:
- A packet was received from the network that had an illegal control
field or UI.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.016 VL selftest_phase
fld error_condition
nt network
- Long Syntax:
- ETH.016 VLAN-E selftest_phase
failed: error_condition
, network network
- Description:
- The selftest for the VLAN-E card has reported an error
during selftest.
- Cause:
- Generally this indicates a hardware error with the card.
- Action:
- Refer to the router hardware manual for more details.
- Level:
- P-TRACE
- Short Syntax:
- ETH.017 LOOP rcv source_Ethernet_address
-> destination_Ethernet_address
, nt network
- Long Syntax:
- ETH.017 Loopback Protocol frame received from source_Ethernet_address
to destination_Ethernet_address
, network network
- Description:
- An Ethernet Loopback Protocol (Configuration Testing Protocol) packet
was received.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.018 LOOP odd skp count
, source_Ethernet_address
-> destination_Ethernet_address
, nt network
- Long Syntax:
- ETH.018 Loopback Protocol, odd skipCount count
from source_Ethernet_address
to destination_Ethernet_address
, network network
- Description:
- An Ethernet Loopback Protocol (Configuration Testing Protocol) packet
had an odd skipCount in the packet. It will be discarded.
- Cause:
- Programming error on remote node.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.019 LOOP func function
not forw, source_Ethernet_address
-> destination_Ethernet_address
, nt network
- Long Syntax:
- ETH.019 Loopback Protocol, function function
not Forward Data from source_Ethernet_address
to destination_Ethernet_address
, network network
- Description:
- An Ethernet Loopback Protocol (Configuration Testing Protocol) packet
did not have a function code of forward (2). It will be discarded.
- Cause:
- Function code was reply (1), because we were the ultimate destination
of this packet.
- Action:
- None.
- Cause:
- Undefined function code, due to programming error in remote node.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.020 LOOP mc fwd dst forward_Ethernet_address
, source_Ethernet_address
-> destination_Ethernet_address
, nt network
- Long Syntax:
- ETH.020 Loopback Protocol, multicast forward address forward_Ethernet_address
from source_Ethernet_address
to destination_Ethernet_address
, network network
- Description:
- An Ethernet Loopback Protocol (Configuration Testing Protocol) packet
has a forward address that is a multicast. It will be discarded.
- Cause:
- Programming error in remote node.
- Level:
- P-TRACE
- Short Syntax:
- ETH.021 LOOP fwd source_Ethernet_address
-> forward_Ethernet_address
, nt network
- Long Syntax:
- ETH.021 Loopback Protocol, forwarding from source_Ethernet_address
to forward_Ethernet_address
, network network
- Description:
- An Ethernet Loopback Protocol (Configuration Testing Protocol) packet
is being forwarded to the specified next hop.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.022 LOOP fwd to forward_Ethernet_address
dsc, rsn code
, nt network
- Long Syntax:
- ETH.022 Loopback protocol, forward to forward_Ethernet_address
discarded, for reason code
, network network
- Description:
- A Ethernet Loopback Protocol (Configuration Testing Protocol)
packet could not be forwarded to the specified
address, for the reason specified by code.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.023 LLC RSP to destination_Ethernet_address
dsc, rsn code
, nt network
- Long Syntax:
- ETH.023 LLC response to destination_Ethernet_address
discarded, for reason code
, network network
- Description:
- An LLC response (XID or TEST) could not be transmitted to the specified
address, for the reason specified by code.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.024 MOP bd ln actual_length
claimed_length
source_Ethernet_address
-> destination_Ethernet_address
nt network
- Long Syntax:
- ETH.024 DECnet MOP packet received with a bad length actual actual_length
claimed claimed_length
from source_Ethernet_address
to destination_Ethernet_address
network network
- Description:
- A DECnet MOP packet was received with a length field that was larger
than the actual length of the packet.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.025 LOOP bd skp count
, source_Ethernet_address
-> destination_Ethernet_address
, nt network
- Long Syntax:
- ETH.025 Loopback Protocol, bad skipCount count
from source_Ethernet_address
to destination_Ethernet_address
, network network
- Description:
- An Ethernet Loopback Protocol (Configuration Testing Protocol) packet
had a skipCount in the packet that points to beyond the end
of the packet. It will be discarded.
- Cause:
- Programming error on remote node.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.026 unkn SNAP mfr cd mfr_code_1
mfr_code_2
mfr_code_3
fm source_Ethernet_address
nt network
- Long Syntax:
- ETH.026 packet received with unknown SNAP Manufacture's code mfr_code_1
mfr_code_2
mfr_code_3
from source_Ethernet_address
network network
- Description:
- A SNAP packet was received with an unknown or unsupported
manufacture's code. (STB)
- Level:
- C-INFO
- Short Syntax:
- ETH.027 protocol_type
pkt flt for prot = protocol
, nt network
- Long Syntax:
- ETH.027 protocol_type
type pakcet filtered for protocol = protocol
network network
- Description:
- Protocol type like, Ethertype, DSAPytpe or SNAPtype packet filtered.
This is due to the user supplied protocol filtering information. (STB)
- Level:
- C-INFO
- Short Syntax:
- ETH.028 DROP, proto= protocol_type
enb but adr dest_ethernet_addr
not reg, nt network
- Long Syntax:
- ETH.028 Dropped, protocol = protocol_type
enabled but address dest_ethernet_addr
not registered, network network
- Description:
- Packet Droped for an enabled protocol whose destination address
is neither ours nor of interested multicast address. (STB)
- Level:
- C-INFO
- Short Syntax:
- ETH.029 Unprocssd, src port blked, nt network
MAC_source
-> MAC_destination
- Long Syntax:
- ETH.029 MAC frame not processed as incoming port is not in LEARNING or FORWARDING mode on network network
MAC_source
-> MAC_destination
- Description:
- A MAC frame is not being processed as the source port is
not yet in LEARNING or FORWARDING mode. Frame is discarded. (STB).
- Level:
- C-INFO
- Short Syntax:
- ETH.030 SL:-DROP, Bdg Pkt for Enb Proto protocol_type_string
, type = protocol
- Long Syntax:
- ETH.030 Serial line: Dropped bridged packet for enabled protocol protocol_type_string
, protocol type = protocol
- Description:
- A packet received by serial line is dropping bridged packet as the
protocol is enabled. Packets are not bridged if protocol is enabled.
(STB)
- Level:
- UI-ERROR
- Short Syntax:
- ETH.031 NP no buf fr slf-tst, nt network
- Long Syntax:
- ETH.031 NP no buffer for self-test, network network
- Description:
- There was no packet buffer available to do a self-test on the
NP600 interface. The self-test will time out and fail.
- Level:
- C-TRACE
- Short Syntax:
- ETH.032 NP slf-tst cmd, nt network
- Long Syntax:
- ETH.032 NP starting self-test command, network network
- Description:
- The NP600 self-test routine is starting an internal self-test
in the interface. This is done on some self-tests.
- Level:
- C-TRACE
- Short Syntax:
- ETH.033 NP diag cmd, nt network
- Long Syntax:
- ETH.033 NP starting diagnostics, network network
- Description:
- The NP600 self-test routine is starting an internal
diagnostics program in the interface. This is normal for the
first self-test.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.034 NP slf-tst cmd timout, nt network
- Long Syntax:
- ETH.034 NP self-test command timed out, network network
- Description:
- The NP600 self-test running inside the interface did not complete
in the required 5 seconds. This probably indicates a serious
problem with the interface, or with its network connection.
The network will be declared down.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.035 NP diag cmd timout, nt network
- Long Syntax:
- ETH.035 NP diagnostics timed out, network network
- Description:
- The NP600 diagnostics running inside the interface did not complete
in the required 20 seconds. This probably indicates a serious
problem with the interface, or with its network connection.
The network will be declared down.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.036 NP fld module
diag, stat status_code
, nt network
disabled
- Long Syntax:
- ETH.036 NP failed module
diagnostic, status status_code
, network network
disabled
- Description:
- The NP600 internal diagnostics detected a hardware failure.
The interface will be disabled, further self-tests will be cancelled.
Module indicates which major functional block of the
diagnostics failed, and will be one of
"EPROM checksum test",
"Quick DRAM test",
"System memory port test",
"Power-up state test",
"Ethernet address ROM test",
"System memory port and DMA test",
"82586 sanity test",
"CPU timers test",
"Ethernet connection test",
"RDR bit test", or
"Quick DRAM test 12".
The status_code is the exact error number reported by the diagnostics.
NPX00 Micro-Diagnostics" DS-NPX00-0C.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.037 NP diags OK, ETH bad, stat status_code
, nt networ
- Long Syntax:
- ETH.037 NP diagnostics OK, Ethernet connection bad, status status_code
, network networ
- Description:
- The NP600 diagnostics passed, but indicate that the Ethernet
network connection is faulty. The status_code is returned by
the diagnostics. The overall self-test will continue, and will
presumably fail later.
NPX00 Micro-Diagnostics" DS-NPX00-0C, "LAN CONNECTION TEST,
MAJOR TEST NUMBER 0Ah".
- Level:
- UI-ERROR
- Short Syntax:
- ETH.038 NP load timout, nt network
- Long Syntax:
- ETH.038 NP firmware load timed out, network network
- Description:
- The download of the operational firmware by the EPROM monitor
in the NP600 interface timed out. This may indicate a hardware
problem, or it may be an error in DMA channel configuration.
The network will be declared down.
- Level:
- U-TRACE
- Short Syntax:
- ETH.039 NP command
rst, nt network
- Long Syntax:
- ETH.039 NP command
reset, network network
- Description:
- The specified command to the NP600 interface
has been cancelled by a device reset. The command will be
"load" for a firmware load, "slf-tst" for an internal self-test,
or "maint" for a maintenance command.
These messages are a normal follow-on to a timeout.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.040 NP slf-tst fld status_code
, nt network
- Long Syntax:
- ETH.040 NP self-test command failed status status_code
, network network
- Description:
- The NP600 self-test running inside the interface failed.
This probably indicates that the network connection is
faulty. Status_code is the error number from the internal
self-test command.
- Level:
- C-TRACE
- Short Syntax:
- ETH.041 NP loaded, slf-tst, nt network
- Long Syntax:
- ETH.041 NP loaded, doing self-test command, network network
- Description:
- The NP600 firmware load succeeded, so an internal self-test
is being started in the interface.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.042 Unable to get buf for ethernet packet.
- Long Syntax:
- ETH.042 Unable to get buffer for ethernet packet.
- Description:
- A buffer to set an Ethernet address, or to copy an Ethernet
packet couldn't be gotten because of a buffer shortage.
- Level:
- ALWAYS
- Short Syntax:
- ETH.043 CMD596 Command Timeout. Interface network
eing restarted.
- Long Syntax:
- ETH.043 CMD596 Command Timeout. Interface network
eing restarted.
- Description:
- The 82596 chip on the interface card has failed to clear the
command field for this interface. The interface will be re-initialized.
- Level:
- ALWAYS
- Short Syntax:
- ETH.044 I5IOCTL Bad Command network
being restarted.
- Long Syntax:
- ETH.044 I5IOCTL Bad Command network
being restarted.
- Description:
- An Incorrect command field has been sent to the driver. The interface
will be re-initialized.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.045 Eth self-test selftest_phase
fld error_condition
nt network
- Long Syntax:
- ETH.045 Ethernet self-test phase selftest_phase
failed: error_condition
, network network
- Description:
- The selftest for the Ethernet card has reported an error
during selftest. The phases are
"Reset board",
"Reset delay",
"Check reset done",
"Check reset delay",
"Init SCB",
"Init SCB delay",
"Init SCB completion",
"Read hardware address",
"Set bus throttle timers",
"Internal loopback",
"Set hardware address",
"Enable receive",
"Internal loopback (output)",
"Check internal loopback data",
"External loopback",
"External loopback delay",
"External loopback (output)",
"Check external loopback data",
"Network loopback",
"Network loopback delay",
"Network loopback (output)",
"Check network loopback data",
"Clear loopback", and
"Operational test".
- Cause:
- In the "Reset board" phase, the error
"Packetsize of < 1500 bytes" indicates that the interface
has been provided with buffers that are too small.
- Action:
- Correct configuration of system that is artificially reducing
packet size below Ethernet requirement of 1500 bytes.
- Cause:
- In all phases, the error "No buffers"
indicates that there is a severe packet buffer shortage in the
router.
- Action:
- Increase buffer memory size, decrease buffer size on configurable
networks.
- Cause:
- In phase "Init SCB completion", the error "ISCP busy not 0"
indicates that the BUSY byte of the
82596 Intermediate System Configuration Pointer
(ISCP) did not clear after the CA signal was sent.
- Action:
- This indicates a probable hardware problem with the interface
or router. Run diagnostics.
- Cause:
- The error
"Unexpected receive pkt" indicates that the interface recieved
a packet in a self-test state where it did not expect to
receive a packet.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- The error "Loop back count error", indicates that the recieved
loopback packet was not of the same length as the transmitted one.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- The error
"Loop back stat error" indicates that the receive of the loopback
packet had an unsuccessful error status.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- The error
"Loop back data error" indicates that there was a data mismatch in
the loopback packet.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- In the "Operational test" phase, the error "maintenance failure"
indicates that the interface could not perform a sucessful maintenance
test. (The maintenance test sends one packet and checks for
carrier sense.)
- Action:
- Check the transceiver cabling and hardware.
- Cause:
- In all phases, the error "timeout" indicates that the entire
self-test did not complete within one-eighth of a second.
- Level:
- UE-ERROR
- Short Syntax:
- ETH.046 IPX pkt in received_encapsulation
encap ign, using configured_encapsulation
encaps, nt network
- Long Syntax:
- ETH.046 IPX pkt in encapsulation received_encapsulation
ignored, using encapsulation configured_encapsulation
on network network
- Description:
- This message is generated when an IPX packet is received in
a data-link encapsulation (frame) other than the one configured for
IPX on this interface. The packet will be ignored.
The received_encapsulation and configured_encapsulation are one
of
"ETHERNET_802.3",
"ETHERNET_II",
"ETHERNET_802.2", or
"ETHERNET_SNAP". ETHERNET_802.3 is also known as "Novell", and
ETHERNET_II is also known as "Ethernet".
- Cause:
- If only one encapsulation is being used on this network, this node's
encapsulation is not the same as all other IPX nodes on the network.
- Action:
- Configure all nodes on network to use same encapsulation.
- Cause:
- If multiple encapsulations are being used on this network,
a packet has been received from a node using an encapsulation
different from this node.
- Level:
- UI-ERROR
- Short Syntax:
- ETH.047 Eth self-test selftest_phase
fld error_condition
nt network
- Long Syntax:
- ETH.047 Ethernet port self-test phase selftest_phase
failed: error_condition
, network network
- Description:
- The self-test for the SCC Ethernet port has reported an error
during self-test. The phases are
"Reset port",
"Set media selection",
"Set hardware address",
"Network loopback",
"Enable receive",
"Network loopback (output)",
"Check network loopback data",
"Clear loopback",
"Set multicast addresses",
and
"Operational test".
- Cause:
- In the "Reset port" phase, the error
"Packetsize of < 1500 bytes" indicates that the interface
has been provided with buffers that are too small.
- Action:
- Correct the configuration of the system that is artificially reducing
packet size below the Ethernet requirement of 1500 bytes.
- Cause:
- In all phases, the error "No buffers"
indicates that there is a severe packet buffer shortage in the
router.
- Action:
- Increase memory size, decrease size of routing tables,
decrease buffer allocations to networks,
decrease buffer size on configurable networks.
- Cause:
- The error
"Loop back data error" indicates that there was a data mismatch in
the loopback packet.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- The error "Loop back count error" indicates that the received
loopback packet was not of the same length as the transmitted one.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- The error
"Loop back status error" indicates that the receive of the loopback
packet had an unsuccessful error status.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- In all phases, the error "Timeout" indicates that the entire
self-test did not complete within one-eighth of a second.
- Action:
- This indicates a possible hardware problem with the interface.
Run diagnostics.
- Cause:
- In the "Operational test" phase, the error "maintenance failure"
indicates that the interface could not perform a sucessful maintenance
test. (The maintenance test sends one packet and checks for
carrier sense.)
- Action:
- Check the transceiver cabling and hardware. The router is probably not
connected to the Ethernet correctly, or there is a hardware failure.
- Level:
- U-INFO
- Short Syntax:
- ETH.048 Op ovfl nt network ID
- Long Syntax:
- ETH.048 Output overflow when transmitting on Network network ID
- Description:
- When the router went to send a packet, the network
output queue was too full and the router had to discard the packet.
The output overflow counter for that network was incremented,
and the packet was returned to the protocol forwarder for attention.
- Cause:
- The source packet traffic in the input network is higher
than the bandwidth available in the output network. Since the
router itself is keeping up with the traffic, there is little
it can do. The hosts generating the traffic are simply sending
more data than the output network can accommodate.
- Action:
- Increase the speed of the network in question (particularly if it
is a slow speed leased line), or take measures to restrict the
amount of traffic generated on the input network.
- Panic
- ethbdtbl
- Short Syntax:
- ethbdtbl: eth_llc tbl out of date
- Description:
- The Ethernet LLC table is out of date.
- Action:
- Contact customer service.
- Panic
- ethintm
- Short Syntax:
- ethintm: net intf mismtch
- Description:
- The Ethernet data structure "net" is not Ethernet related.
- Action:
- Contact customer service.
- Panic
- ethbprt
- Short Syntax:
- ethbprt: bad prot init
- Description:
- An unsupported Network Layer protocol tried to initialize Ethernet
handler.
- Action:
- Contact customer service.
- Panic
- ethbipx
- Short Syntax:
- ethbipx: bad IPX rqst shd be 8137
- Description:
- An unsupported IPX packet was given to the Ethernet handler for
transmission.
- Action:
- Contact customer service.
- Panic
- ethbreq
- Short Syntax:
- ethbreq: bad xmit rqst
- Description:
- An unsupported protocol packet was given to the Ethernet handler for
transmission.
- Action:
- Contact customer service.
- Panic
- ethtbig
- Short Syntax:
- ethtbig: bad xmit rqst pkt too lg
- Description:
- A packet was given to the Ethernet handler for transmission that was
too large.
- Action:
- Contact customer service.
- Panic
- ethnbuf
- Short Syntax:
- ethnbuf: no buf to set addr
- Description:
- A buffer to set an Ethernet address could not be allocated.
- Action:
- Contact customer service.
- Panic
- ethsrtmcr
- Short Syntax:
- ethsrtmcr: multicast address previously reserved
- Description:
- One of the multicast addresses enabled on this interface is
one of the multicast addresses in the range 01-80-C2-00-00-00
through 01-80-C2-00-00-0F.
- Cause:
- Possibly one of these addresses that is being used by a protocol where
the user can select the multicast address, such as the ES-IS
and IS-IS protocols in ISO.
- Action:
- Don't use the reserved addresses.
- Panic
- ethsrtnm
- Short Syntax:
- ethsrtnm: no memory to register own MAC addr
- Description:
- The learning database is so small that there are not enough
free entries to learn the address of this interface.
- Action:
- Increase the size of the learning database.
- Panic
- ethsrtnmm
- Short Syntax:
- ethsrtnmm: no memory to register mutlicast address
- Description:
- The learning database is so small that there are not enough
free entries to one of the multicast addresses of this interface.
- Action:
- Increase the size of the learning database.
- Fatal
- ethsrtun
- Short Syntax:
- ethsrtun: unsupported command
- Description:
- An unsupported command was given by the SRT protocol
- Panic
- ilnie
- Short Syntax:
- ilnie: nt Ilan Eth
- Description:
- The Interlan Ethernet initialization routine was called, but the
network it was operating on was not an Interlan Ethernet.
- Panic
- ilcai
- Short Syntax:
- ilcai: cnt alloc ildb
- Description:
- The Interlan Ethernet initialization routine could not allocate
memory it needed for internal data structures.
- Panic
- penpe
- Short Syntax:
- penpe: nt Pteon Eth
- Description:
- The Ethernet initialization routine was called, but the
network it was operating on was not a Ethernet.
- Panic
- pecap
- Short Syntax:
- pecap: cnt alloc
- Description:
- The Ethernet initialization routine could not allocate
memory it needed for internal data structures.
- Panic
- npnnp
- Short Syntax:
- npnnp: nt NP600
- Description:
- The NP600 initialization routine was called, but the
network it was operating on was not a NP600 Ethernet.
- Panic
- npcap
- Short Syntax:
- npcap: cnt alloc
- Description:
- The NP600 Ethernet initialization routine could not allocate
memory it needed for internal data structures.