[Top] [Prev] [Next] [Bottom]

Appendix A

Specifications

This appendix provides the specifications for the 3000 Series Secure Gateway Router and each of its modules.

3000 Series Secure Gateway Router Specifications

Analog Voice Module Specifications

DDS CSU/DSU Module Specifications

Ethernet Module Specifications

T1 CSU/DSU Module Specifications

3000 Series Secure Gateway Router Specifications


Processor	MC 68EN360, 33 MHz
Memory DRAM Flash	8 MB (expandable to 24, 40, or 72 MB) 8 MB
VPN	Optional hardware assist for data encryption, authentication, and compression
Input/Output Interfaces	Console, RS-232 async Ethernet 10BaseT 3 modular slots for data routing Optional voice interface with either 2- or 4-port analog
Dimensions	17.25 x 10 x 1.75 inches
Weight	10 lbs
Power	100-240 VAC 50-60 Hz 1.4A MAX
Operating Temperature	41-105 degrees F 5-41 degrees C
Relative Humidity	8-80%
Heat Dissipation	60 Watts, maximum 205 BTUs
Agency Approvals	EMI— FCC Part 15 Class A; CISPR 22 Class A; EN55022 Telecom— FCC Part 68, CS03, CTR2, I-CTR3, CTR 12/A1, CTR13 Safety— UL 1950, CSA 22.2, TS.001, AS/NZS3260, EN60950 CB scheme for all countries Immunity— IEC 801-2, 801-3, 801-4

Analog Voice Module Specifications

The following table lists the specifications for the analog voice module.

Interface Types

Two-wire FXS loop/start

Two-wire FXO loop/ground start and two-wire FXS loop/start

Two-wire FXO loop/ground start

Two- or four-wire E & M type I, II, and V

Dialing DTMF or pulse (10 or 20 pps)

Co-processor MPC850, 50 MHz

Signalling Wink start, delay dial, immediate start, hoot and holler, and phone

Indicator One multicolored status LED

Interface Types	Two-wire FXS loop/start Two-wire FXO loop/ground start and two-wire FXS loop/start Two-wire FXO loop/ground start Two- or four-wire E & M type I, II, and V
Dialing	DTMF or pulse (10 or 20 pps)
Co-processor	MPC850, 50 MHz
Signalling	Wink start, delay dial, immediate start, hoot and holler, and phone
Indicator	One multicolored status LED

DDS CSU/DSU Module Specifications

The following table lists the specifications for the DDS CSU/DSU module.


Speed	56 or 64 Kbps, primary channel
Protocol	Sync, full duplex
Connector	RJ-48S
Indicators	Alarm, Test Mode, Loss of Synchronization
Diagnostics	CSU loopback, DSU non-latching loopback (except 64 Kbps mode)
Clocking	Internal, Network
Line Coding	AMI, B8ZS
FIC	04DUS-56
SOC	6.0N

E1 Module Specifications

The following table lists the specifications for the E1 module.


Speed	2.048 Mbps
Data Rate	N x 64 Kbps up to 2.048 Mbps
Impedance	120 ohm
Connector	RJ-48C
Indicators	Alarm, Test Mode, Loss of Synchronization
Diagnostics	Local, remote, and V.54 loopbacks
Clocking	Internal, Network
Line Coding	HBD3
Line Framing	G.704, Structured & Unstructured

Ethernet Module Specifications

The following table lists the specifications for Ethernet module.


Interface	IEEE 802.3, 10BaseT With signal crossover switch
Connector	RJ-45
Indicators	Activity, Link status

ISDN Module Specifications

ISDN U

The following table lists the specifications for the ISDN U module.

Standards ANSI T1.601

Data Rate 144 Kbps

Data Structure 2B + D

Bit Rate 160 Kbps

Connector RJ-49C

Indicators D Channel Status, (2) B Channel Status

Line Coding 2B1Q

FIC 02IS5

SOC 6.0N

Standards	ANSI T1.601
Data Rate	144 Kbps
Data Structure	2B + D
Bit Rate	160 Kbps
Connector	RJ-49C
Indicators	D Channel Status, (2) B Channel Status
Line Coding	2B1Q
FIC	02IS5
SOC	6.0N

ISDN S/T

The following table lists the specifications for the ISDN S/T module.

Standards CCITT I.430

Data Rate 144 Kbps

Data Structure 2B + D

Bit Rate 192 Kbps

Connector RJ-61x, 2-pair conductor

Indicators D Channel Status, (2) B Channel Status

Line Coding Pseudo-tenary

Standards	CCITT I.430
Data Rate	144 Kbps
Data Structure	2B + D
Bit Rate	192 Kbps
Connector	RJ-61x, 2-pair conductor
Indicators	D Channel Status, (2) B Channel Status
Line Coding	Pseudo-tenary

SDSL Module Specifications

The following table lists the specifications for the SDSL module.

Line Speed 144 Kbps to 2.320 Mbps

Interface Single pair

Connector RJ-48C

Indicators Alarm, Test Mode, Loss of Synchronization

Signalling 2B1Q

Impedance 135 ohm

Diagnostics Local and remote loopback

Line Speed	144 Kbps to 2.320 Mbps
Interface	Single pair
Connector	RJ-48C
Indicators	Alarm, Test Mode, Loss of Synchronization
Signalling	2B1Q
Impedance	135 ohm
Diagnostics	Local and remote loopback

T1 CSU/DSU Module Specifications

The following table lists the specifications for the T1 CSU/DSU module.


Speed	1.544 Mbps
Data Rate	N x 56 Kbps, N x 64 Kbps up to 1.536 Mbps
Impedance	100 ohm
Connector	RJ-48C
Indicators	Alarm, Test Mode, Loss of Sync
Diagnostics	Local, remote, and V.54 loopbacks
Clocking	Internal, Network
Line Coding	B8ZS
Line Framing	Extended Super Frame (ESP)
Transmit LBO	0 to -22dB
FIC	04DU9-BN,DN,1KN,1SN
SOC	6.0N

WAN Module Specifications

The following table lists the specifications for the WAN module.

WAN Speed 4.8 Kbps to 2.048 Mbps

Interfaces V.35, RS232/V.24, X.21 (DTE and DCE)

Connector DB 44
Use the appropriate external WAN cable. See Selecting a WAN Cable on page 18

WAN Speed	4.8 Kbps to 2.048 Mbps
Interfaces	V.35, RS232/V.24, X.21 (DTE and DCE)
Connector	DB 44 Use the appropriate external WAN cable. See Selecting a WAN Cable on page 18

[Top] [Prev] [Next] [Bottom]