ELS Messages for NetWare Link Services Protocol (NLSP)

NLSP.001

Level:
P-TRACE
Class:
FAKE
Short Syntax:
NLSP.001 pkt frm source_net / source_node , IPX circuit ID acket from %X/%E ignored, %S
Long Syntax:
NLSP.001 Packet from source_net / source_node ignored, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet has arrived on a circuit. The NLSP feature is not in this router load. The packet is discarded.

NLSP.002

Level:
UI-ERROR
Short Syntax:
NLSP.002 no buf for WANH, IPX circuit ID o buffer for WAN Hello, %S
Long Syntax:
NLSP.002 no buffer for WAN Hello, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
No packet buffer is available to send a WAN Hello packet.

NLSP.003

Level:
UI-ERROR
Short Syntax:
NLSP.003 no buf for LSP, IPX circuit ID o buffer for Link State Packet, %S
Long Syntax:
NLSP.003 no buffer for Link State Packet, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
No packet buffer is available to send a LSP, Link State Packet.

NLSP.004

Level:
UI-ERROR
Short Syntax:
NLSP.004 no buf for SNP, IPX circuit ID o buffer for SNP, %S
Long Syntax:
NLSP.004 no buffer for SNP, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
No packet buffer is available to send a sequence numbered packet. A sequenced number packet is either a CSNP or a PSNP.

NLSP.005

Level:
P-TRACE
Short Syntax:
NLSP.005 Snt LANH, ht= hold_time , pr= priority , DR= NLSP circuit ID , IPX circuit ID ent LAN Hello, holding time=%d, priority=%d, DR=%E:%02X, %S
Long Syntax:
NLSP.005 Sent LAN Hello, holding time= hold_time , priority= priority , DR= NLSP circuit ID , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A LAN hello packet has been sent on the circuit. The packet's holding time, priority, and designated router (DR) are shown. The designated router is the circuit's designated router from this router's point of view.

NLSP.006

Level:
UI-ERROR
Short Syntax:
NLSP.006 LANH send failed, reason= reason_code , IPX circuit ID AN Hello send failed, reason=%d, %S
Long Syntax:
NLSP.006 LAN Hello send failed, reason= reason_code , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A request to send a LAN hello packet was rejected and failed due to the indicated reason. See reasons under IPX.108.

NLSP.007

Level:
UI-ERROR
Short Syntax:
NLSP.007 bad pkt type= nlsp_packet_type , IPX circuit ID ad packet type=%x, %S
Long Syntax:
NLSP.007 bad packet type= nlsp_packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains an NLSP packet type that is unknown to this implementation of NLSP. The packet is discarded.
Cause:
Badly formatted NLSP packet.
Cause:
Future versions of NLSP may support other packet types.
Action:
Consult migration strategy.

NLSP.008

Level:
UI-ERROR
Short Syntax:
NLSP.008 bad maj version= nlsp_major_version , from src_ipx_node on IPX circuit ID ad major version=%d, from %E on %S
Long Syntax:
NLSP.008 bad major version= nlsp_major_version , from src_ipx_node on IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains a major version number larger than the major version number of this implementation of NLSP. The packet is discarded.
Cause:
Future versions of NLSP may have a higher major version numbers.
Action:
Consult migration strategy.

NLSP.009

Level:
UI-ERROR
Short Syntax:
NLSP.009 pktRxSmall from src_ipx_node , pkt= packet_type , IPX circuit ID acketRxSmall from %E, packet type=%s, %S
Long Syntax:
NLSP.009 packetRxSmall from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains a length in the NLSP header that is inconsistent with the length in the IPX header. The packet is discarded. The packet type is one of LANH, WANH, LSP, CNSP, or PNSP. The sender's IPX node number is given.

NLSP.010

Level:
UI-ERROR
Short Syntax:
NLSP.010 LANH from src_ipx_node on WAN circ, IPX circuit ID AN Hello from %E on WAN circuit, %S
Long Syntax:
NLSP.010 LAN Hello from src_ipx_node on WAN circuit, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A NLSP LAN Hello packet, which is only used on broadcast circuits, was received on a IPXWAN circuit. The packet is discarded.
Cause:
Configuration inconsistency. Another router has the circuit configured as a broadcast circuit. This router has the circuit configured as an IPXWAN circuit.
Action:
Configure both routers the same way for the circuit.
Cause:
Possible NLSP implementation error.
Action:
Fix the router sending the LAN hello.

NLSP.011

Level:
UI-ERROR
Short Syntax:
NLSP.011 L2 pkt from src_ipx_node on L1 circ, IPX circuit ID evel 2 from %E packet on a level 1 circuit, %S
Long Syntax:
NLSP.011 Level 2 from src_ipx_node packet on a level 1 circuit, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A packet marked as a level 2 packet was received on this circuit, which is only capable of level 1. The packet is discarded.
Cause:
In the future versions of NLSP, there may be a level 2 circuit.
Action:
Consult migration strategy.

NLSP.012

Level:
UI-ERROR
Short Syntax:
NLSP.012 MTU malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID TU malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.012 MTU malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a malformed MTU option, maximum transmission unit, option. See NLSP.009 for packet types. The packet is discarded.

NLSP.013

Level:
UI-ERROR
Short Syntax:
NLSP.013 AA malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID A malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.013 AA malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a malformed Area Addresses option. See NLSP.009 for packet types. The packet is discarded.

NLSP.014

Level:
UI-ERROR
Short Syntax:
NLSP.014 nbr malformOpt from src_ipx_node on LANH, IPX circuit ID eighbor malformedOption from %E on LAN Hello, %S
Long Syntax:
NLSP.014 neighbor malformedOption from src_ipx_node on LAN Hello, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A LAN Hello NLSP packet was received with a malformed neighbor option. The packet is discarded.

NLSP.015

Level:
UI-ERROR
Short Syntax:
NLSP.015 MTU missOpt from src_ipx_node , pkt= packet_type , IPX circuit ID TU missingOption from %E, packet type=%s, %S
Long Syntax:
NLSP.015 MTU missingOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a no MTU option, which is a required option for LAN Hello and WAN Hello packets. See NLSP.009 for packet types. The packet is discarded.

NLSP.016

Level:
UI-ERROR
Short Syntax:
NLSP.016 AA missOpt from src_ipx_node , pkt= packet_type , IPX circuit ID A missingOption from %E, packet type=%s, %S
Long Syntax:
NLSP.016 AA missingOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a no Area Addresses option, which is a required option for LAN Hello and WAN Hello packets. See NLSP.009 for packet types. The packet is discarded.

NLSP.017

Level:
UI-ERROR
Short Syntax:
NLSP.017 malformOpt from src_ipx_node : total len, pkt= packet_type , IPX circuit ID alformedOption from %E: total length, packet type=%s, %S
Long Syntax:
NLSP.017 malformedOption from src_ipx_node : total length, packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains options, whose total length does not exactly match the total length of the packet. See NLSP.009 for packet types. The packet is discarded.

NLSP.018

Level:
UI-ERROR
Short Syntax:
NLSP.018 Mismatched Net Number from src_ipx_node , pkt= packet_type , IPX circuit ID ismatched Network Number from %E, packet type=%s, %S
Long Syntax:
NLSP.018 Mismatched Network Number from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The source IPX network number in the IPX header does not match the configured network number for this broadcast circuit. See NLSP.009 for packet types. The packet is discarded.
Cause:
Configuration of IPX network numbers are mismatched. This must be fixed before the two routers can interoperate. All configured network numbers on the IPX network should be the same.
Action:
Adjust configuration to make IPX network numbers match.

NLSP.019

Level:
UI-ERROR
Short Syntax:
NLSP.019 mismatchedNodeAddress LANH from ipx_node , IPX circuit ID ismatchedNodeAddress in LAN Hello from %E, %S
Long Syntax:
NLSP.019 mismatchedNodeAddress in LAN Hello from ipx_node , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The IPX header of a received LAN Hello packet contains a source IPX network node that does not match the sender's NIC address. The packet is discarded.
Cause:
Unknown, but proper operation of IPX requires these to match.
Action:
Adjust configuration or fix NLSP implementation to make IPX node numbers match.

NLSP.020

Level:
UI-ERROR
Short Syntax:
NLSP.020 areaMismatch LANH from ipx_node , IPX circuit ID reaMismatch in LAN Hello from %E, %S
Long Syntax:
NLSP.020 areaMismatch in LAN Hello from ipx_node , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The received LAN Hello packet contains no area address that matches any of our area addresses. The packet is discarded.
Cause:
Possible misconfiguration of area addresses.
Action:
Adjust configuration of the area addresses.

NLSP.021

Level:
C-INFO
Short Syntax:
NLSP.021 no multicast support on ipx_node , IPX circuit ID o multicast support on %E, %S
Long Syntax:
NLSP.021 no multicast support on ipx_node , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The received LAN Hello packet indicated that the sending router does not support the NLSP multicast address. To allow the routers to interoperate, this router is automatically switching over to send NLSP packets using the LAN broadcast address instead of the NLSP LAN multicast address on this circuit.
Cause:
One of the routers on the LAN either can not support or is configured to not support the NLSP multicast address.
Action:
None. Everything is automatic. The message is just information. However, the circuit may be configured to always use the broadcast address if a workaround is ever needed for a situation involving interoperability with other router's support of the NLSP multicast address.

NLSP.022

Level:
C-INFO
Short Syntax:
NLSP.022 new LAN nbr system_id , IPX circuit ID ew LAN neighbor %E, %S
Long Syntax:
NLSP.022 new LAN neighbor system_id , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received LAN Hello packet on the circuit has identified a new NLSP neighbor. The adjacency is placed into the initialization state.

NLSP.023

Level:
C-INFO
Short Syntax:
NLSP.023 LAN nbr system_id , init->up, IPX circuit ID AN neighbor %E, init->up, %S
Long Syntax:
NLSP.023 LAN neighbor system_id , init->up, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received LAN Hello packet on the circuit shows that the neighbor sees this router and this router sees the neighbor. The adjacency with the neighbor is now in the up state.

NLSP.024

Level:
C-INFO
Short Syntax:
NLSP.024 LAN nbr system_id , up->init, IPX circuit ID AN neighbor %E, up->init, %S
Long Syntax:
NLSP.024 LAN neighbor system_id , up->init, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received LAN Hello packet on the circuit shows that the LAN neighbor no longer sees us as a neighbor; therefore the state of the adjacency is moved back to the initializing state.

NLSP.025

Level:
C-INFO
Short Syntax:
NLSP.025 This router elected DR, pr= priority , IPX circuit ID his router elected DR, priority=%d, %S
Long Syntax:
NLSP.025 This router elected DR, priority= priority , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
This router has just been newly elected as the designated router on the circuit. The priority is given.

NLSP.026

Level:
C-INFO
Short Syntax:
NLSP.026 This router resigns as DR, IPX circuit ID his router resigns as DR, %S
Long Syntax:
NLSP.026 This router resigns as DR, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
This router has just resigned as designated router on the circuit.

NLSP.027

Level:
C-INFO
Short Syntax:
NLSP.027 New other Router system_id / source_mac elected DR, pr= priority , IPX circuit ID ew other Router %E/%E elected DR, priority=%d, %S
Long Syntax:
NLSP.027 New other Router system_id / source_mac elected DR, priority= priority , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A router, other than this one, has just been newly elected as the DR on the circuit. The router's system_id, source MAC address, and priority are given.

NLSP.028

Level:
C-TRACE
Short Syntax:
NLSP.028 Election: DR= system_id / source_mac , pr= priority , lan_id= NLSP circuit ID IPX circuit ID lection: DR=%E/%E, priority=%d, lan_id=%E:%02X %S
Long Syntax:
NLSP.028 Election: DR= system_id / source_mac , priority= priority , lan_id= NLSP circuit ID IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The election process has run. The elected router's system_id and source MAC address are shown. The elected router's priority and lan_id are shown.

NLSP.029

Level:
P-TRACE
Short Syntax:
NLSP.029 Rcvd LANH from system_id / source_mac , ht= hold_time , pr= priority , lan_id= NLSP circuit ID , IPX circuit ID cvd LAN Hello from %E/%E, holding time=%d, priority=%d, lan_id=%E:%02X, %S
Long Syntax:
NLSP.029 Rcvd LAN Hello from system_id / source_mac , holding time= hold_time , priority= priority , lan_id= NLSP circuit ID , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A valid LAN hello packet has been received on the circuit from another router. The sending router's system id and source MAC address are shown. The packet's holding time, priority, and lan_id values are shown.

NLSP.030

Level:
UI-ERROR
Short Syntax:
NLSP.030 WANH from src_ipx_node , wrg prot, IPX circuit ID AN Hello from %E, wrong protocol, %S
Long Syntax:
NLSP.030 WAN Hello from src_ipx_node , wrong protocol, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A NLSP WAN Hello packet, which is only used on IPXWAN circuits that have negiotiated the NLSP protocol, was received on the circuit. The packet is discarded.
Cause:
Configuration inconsistency. Another router has the circuit configured as a IPXWAN circuit using NLSP. This router has the circuit configured as an broadcast circuit, or is a WAN circuit that has negiotated something a protocol for the circuit other than the NLSP protocol.
Action:
Configure both routers the same way for the circuit.
Cause:
Possible NLSP implementation error.
Action:
Fix the router sending the WAN hello.

NLSP.031

Level:
UI-ERROR
Short Syntax:
NLSP.031 L2 pkt on L1 circ from NLSP circuit ID , IPX circuit ID evel 2 packet on a level 1 circuit from %E:%02X, %S
Long Syntax:
NLSP.031 Level 2 packet on a level 1 circuit from NLSP circuit ID , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A packet marked as a level 2 packet was received on this WAN circuit, which is only capable of level 1. The packet is discarded.
Cause:
In the future versions of NLSP, there may be a level 2 circuit.
Action:
Consult migration strategy.

NLSP.032

Level:
C-INFO
Short Syntax:
NLSP.032 WAN nbr NLSP circuit ID UP, IPX circuit ID AN neighbor %E:%02X UP, %S
Long Syntax:
NLSP.032 WAN neighbor NLSP circuit ID UP, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The IPXWAN circuit's neighbor state has changed to the up state.

NLSP.033

Level:
UI-ERROR
Short Syntax:
NLSP.033 WANH send failed, reason= reason_code , IPX circuit ID AN Hello send failed, reason=%d, %S
Long Syntax:
NLSP.033 WAN Hello send failed, reason= reason_code , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A request to send a WAN hello packet was rejected and failed due to the indicated reason. See reasons under IPX.108.

NLSP.034

Level:
P-TRACE
Short Syntax:
NLSP.034 Snt WANH, ht= hold_time , st= state , id= circuit_number , IPX circuit ID ent WAN Hello, holding time=%d, state=%s, id=%d, %S
Long Syntax:
NLSP.034 Sent WAN Hello, holding time= hold_time , state= state , id= circuit_number , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A WAN hello packet has been sent on the circuit. The packet's holding time, neighbor state, and local circuit number are shown. The state is UP, INIT, or DOWN and is a key part of the NLSP WANH protocol.

NLSP.035

Level:
P-TRACE
Short Syntax:
NLSP.035 pkt from non-adj ipx_node , pkt= packet_type , IPX circuit ID kt from non-adjacency %E, packet type=%s, %S
Long Syntax:
NLSP.035 pkt from non-adjacency ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A PSNP, CSNP, or LSP packet has been received on the circuit from the given IPX node. However, since a an adjacency has not been established with this node, the packet is discarded.

NLSP.036

Level:
U-TRACE
Short Syntax:
NLSP.036 PSNP from ipx_node dsc, not DR, IPX circuit ID SNP from %E discarded, not DR, %S
Long Syntax:
NLSP.036 PSNP from ipx_node discarded, not DR, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A Partial Sequence Number Packet has been received on a broadcast circuit from the given IPX node. However, since this router is not the designated router on the circuit, the packet is discarded.

NLSP.037

Level:
U-INFO
Short Syntax:
NLSP.037 CSNP from ipx_node dsc, DR, IPX circuit ID SNP from %E discarded, DR, %S
Long Syntax:
NLSP.037 CSNP from ipx_node discarded, DR, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A Complete Sequence Number Packet has been received on the circuit from the given IPX node. However, since this router is the designated router on the circuit and since designated routers do not receive CSNPs, the packet is discarded.
Cause:
Two different routers both think they are the designated router. As a general statement, this should not happen, but it is possible during a brief transitional period as routers decide who is the designated router.
Action:
Investigate possible misconfiguration or possible NLSP router malfunction if the problem persists.

NLSP.038

Level:
UI-ERROR
Short Syntax:
NLSP.038 LSP malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID SP malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.038 LSP malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains a malformed LSP option. See NLSP.009 for packet types. The packet is discarded.

NLSP.039

Level:
UI-ERROR
Short Syntax:
NLSP.039 LSP missOpt from src_ipx_node , pkt= packet_type , IPX circuit ID SP missingOption from %E, packet type=%s, %S
Long Syntax:
NLSP.039 LSP missingOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet was missing the LSP option. The LSP option is a required option for PSNP packets. See NLSP.009 for packet types. The packet is discarded.

NLSP.040

Level:
UI-ERROR
Short Syntax:
NLSP.040 LSP from src_ipx_node , too large, IPX circuit ID SP from %E, too large, %S
Long Syntax:
NLSP.040 LSP from src_ipx_node , too large, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received LSP exceeds the actual max packet size for the circuit. The packet is discarded.
Cause:
The buffer size supported on this router interface is smaller than the LSP packet received.
Action:
Raise buffer size supported on this router interface.
Action:
Reconfigure the NLSP routers that are sending the large LSP packets to use the standard size LSP packet size, i.e. 512 bytes.

NLSP.041

Level:
UI-ERROR
Short Syntax:
NLSP.041 LSP from src_ipx_node , bad chksum, IPX circuit ID SP from %E, bad chksum, %S
Long Syntax:
NLSP.041 LSP from src_ipx_node , bad chksum, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received LSP has a checksum error. The packet is discarded.

NLSP.042

Level:
UI-ERROR
Short Syntax:
NLSP.042 Mgnt Info malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID gnt Info malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.042 Mgnt Info malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a malformed Management Information option. See NLSP.009 for packet types. The packet is discarded.

NLSP.043

Level:
UI-ERROR
Short Syntax:
NLSP.043 LI malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID I malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.043 LI malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a malformed Link Information option. See NLSP.009 for packet types. The packet is discarded.

NLSP.044

Level:
UI-ERROR
Short Syntax:
NLSP.044 Services Info malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID ervices Info malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.044 Services Info malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a malformed Services Information option. See NLSP.009 for packet types. The packet is discarded.

NLSP.045

Level:
UI-ERROR
Short Syntax:
NLSP.045 Ext Rtes malformOpt from src_ipx_node , pkt= packet_type , IPX circuit ID xt Rtes malformedOption from %E, packet type=%s, %S
Long Syntax:
NLSP.045 Ext Rtes malformedOption from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet was received with a malformed External Routes option. See NLSP.009 for packet types. The packet is discarded.

NLSP.046

Level:
U-INFO
Short Syntax:
NLSP.046 LAN nbr system_id aged out: ht= hold_time , IPX circuit ID AN nbr %E aged out: holding time=%d, %S
Long Syntax:
NLSP.046 LAN nbr system_id aged out: holding time= hold_time , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A valid LAN hello packet has not been received from a neighbor within its holding time. The neighbor is removed.
Cause:
Neighboring NLSP router is no longer functioning on this circuit from an NLSP point of view.
Action:
If unexpected, investigate for possible crash, cable disconnect, etc. at the neighboring router.

NLSP.047

Level:
P-TRACE
Short Syntax:
NLSP.047 Rcvd WANH from NLSP circuit ID , ht= hold_time , st= state , IPX circuit ID cvd WAN Hello from %E:%02X, holding time=%d, state=%s, %S
Long Syntax:
NLSP.047 Rcvd WAN Hello from NLSP circuit ID , holding time= hold_time , state= state , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A valid WAN hello packet has been received on an IPXWAN circuit from the other router. The other router's circuit ID is shown. The circuit ID is the system id of the other router plus the its local circuit number for the circuit. The holding time and state is shown.

NLSP.048

Level:
C-INFO
Short Syntax:
NLSP.048 WAN nbr NLSP circuit ID DOWN, IPX circuit ID AN neighbor %E:%02X DOWN, %S
Long Syntax:
NLSP.048 WAN neighbor NLSP circuit ID DOWN, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The IPXWAN circuit's neighbor state has changed to the down state.

NLSP.049

Level:
C-INFO
Short Syntax:
NLSP.049 WAN nbr NLSP circuit ID INIT, IPX circuit ID AN neighbor %E:%02X INIT, %S
Long Syntax:
NLSP.049 WAN neighbor NLSP circuit ID INIT, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The IPXWAN circuit's neighbor state has changed to the initilizing state.

NLSP.050

Level:
UI-ERROR
Short Syntax:
NLSP.050 areaMismatch from NLSP circuit ID new st=DOWN, IPX circuit ID reaMismatch from %E:%02X new state=DOWN, %S
Long Syntax:
NLSP.050 areaMismatch from NLSP circuit ID new state=DOWN, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The received WAN Hello packet contains no area address that matches any of our area addresses. The neighbor state is changed to DOWN.

NLSP.051

Level:
UI-ERROR
Short Syntax:
NLSP.051 wrongSystemType from NLSP circuit ID new st=DOWN, IPX circuit ID ongSystemType from %E:%02X new state=DOWN, %S
Long Syntax:
NLSP.051 wrongSystemType from NLSP circuit ID new state=DOWN, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The received WAN Hello packet has an invalid circuit leveltype. The neighbor state is changed to DOWN.

NLSP.052

Level:
UI-ERROR
Short Syntax:
NLSP.052 circuitIDmismatch from NLSP circuit ID new st=DOWN, IPX circuit ID ircuitIDmismatch from %E:%02X new state=DOWN, %S
Long Syntax:
NLSP.052 circuitIDmismatch from NLSP circuit ID new state=DOWN, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The received WAN Hello packet has informatation that results in a different circuit ID for the IPXWAN connection. The neighbor state is changed to DOWN.

NLSP.053

Level:
UI-ERROR
Short Syntax:
NLSP.053 tooManyAdjacencies: actmaxpktsz= actual_packet_size , IPX circuit ID ooManyAdjacencies: actual maximum packet size=%d, %S
Long Syntax:
NLSP.053 tooManyAdjacencies: actual maximum packet size= actual_packet_size , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
During the building of a LAN Hello, there were too many neighbors to fit them into a single LAN Hello packet. The packet size of a LAN Hello packet is limited to the actual maximum packet size on the circuit, which is shown in the message. The packet is still built and sent with as many neighbors as can fit. The actual maxmimum packet size is the smaller of the packet sizes supported by all the neighbors, but it must still be at least a minimum of 576 bytes.
Cause:
There too NLSP neighbors on this LAN to fit within the actual maximum packet size of a LAN Hello packet.
Action:
Reconfigure the network to reduce the number of NLSP neighbors.
Action:
Check if the configuration of one of the routers needs adjusting to increase its maximum packet size supported.

NLSP.054

Level:
UI-ERROR
Short Syntax:
NLSP.054 OverLoad, entering wait state
Long Syntax:
NLSP.054 OverLoad, entering wait state
Description:
There was insufficient memory resources to store link state in the data base. The wait state is being entered.

NLSP.055

Level:
UI-ERROR
Short Syntax:
NLSP.055 OverLoaded, already in wait state
Long Syntax:
NLSP.055 OverLoaded, already in wait state
Description:
While already in the waiting state, there were insufficient memory resources to store link state in the data base.

NLSP.056

Level:
UI-ERROR
Short Syntax:
NLSP.056 leaving wait state
Long Syntax:
NLSP.056 leaving wait state
Description:
The waiting timer has expired and is leaving the wait state.

NLSP.057

Level:
UI-ERROR
Short Syntax:
NLSP.057 duplicateLSPSystemID: system_id from net internal_network_number
Long Syntax:
NLSP.057 duplicateLSPSystemID: system_id from network internal_network_number
Description:
An LSP arrived with the same LSP ID as our non-psuedonode number 0. The management information inside of the LSP shows a different internal network number from ours.
Cause:
A mis-configuration where two different routers have the same NLSP System ID.
Action:
Find the duplicate router and fix. NLSP can not work properly with two routers that have the same NLSP System ID.

NLSP.058

Level:
UI-ERROR
Short Syntax:
NLSP.058 duplicateInternalNet: internal_network_number with router name router_name
Long Syntax:
NLSP.058 duplicateInternalNet: internal_network_number with router name router_name
Description:
An LSP arrived with the same LSP ID as our non-psuedonode number 0. The management information inside of the LSP shows a different router name from ours.
Cause:
A mis-configuration where two different routers have the same NLSP System ID and internal network numbers.
Action:
Find the duplicate router and fix. NLSP can not work properly with two routers that have the same NLSP System ID. NSLP can not work properly with two routers that have the same internal network number.

NLSP.059

Level:
UI-ERROR
Short Syntax:
NLSP.059 LSP send failed, reason= reason_code , IPX circuit ID SP send failed, reason=%d, %S
Long Syntax:
NLSP.059 LSP send failed, reason= reason_code , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A request to send an LSP packet was rejected and failed due to the indicated reason. See reasons under IPX.108.

NLSP.060

Level:
P-TRACE
Short Syntax:
NLSP.060 Snt LSP: LSP ID sn= sequence_number rtim= remaining_time ck= checksum len= pkt_len IPX circuit ID ent LSP: %E:%02X:%02X sequence_number=%X remaining_time=%d checksum=%X length=%d, %S
Long Syntax:
NLSP.060 Sent LSP: LSP ID sequence_number= sequence_number remaining_time= remaining_time checksum= checksum length= pkt_len , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An LSP packet has been sent on the circuit. The LSP packet's 8-byte LSP ID, sequence number, remaining time, checksum, and length fields are shown. The LSP ID is made up of: the 6-byte NLSP system ID, the local circuit number, and the lsp number. The length is the length of the NLSP packet, and does not include the 30-byte IPX header or the data link header.

NLSP.061

Level:
UI-ERROR
Short Syntax:
NLSP.061 CSNP send failed, reason= reason_code , IPX circuit ID SNP send failed, reason=%d, %S
Long Syntax:
NLSP.061 CSNP send failed, reason= reason_code , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A request to send an CSNP packet was rejected and failed due to the indicated reason. See reasons under IPX.108.

NLSP.062

Level:
UI-ERROR
Short Syntax:
NLSP.062 PSNP send failed, reason= reason_code , IPX circuit ID SNP send failed, reason=%d, %S
Long Syntax:
NLSP.062 PSNP send failed, reason= reason_code , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A request to send an PSNP packet was rejected and failed due to the indicated reason. See reasons under IPX.108.

NLSP.063

Level:
P-TRACE
Short Syntax:
NLSP.063 Snt CSNP: start_sn= LSP ID , end_sn= LSP ID , num= number_entries , IPX circuit ID nt CSNP: start_sn=%E:%02X:%02X, end_sn=%E:%02X:%02X, number_entries=%d, %S
Long Syntax:
NLSP.063 Snt CSNP: start_sn= LSP ID , end_sn= LSP ID , number_entries= number_entries , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A CSNP packet has been sent on the circuit. The starting and ending LSPIDs are shown; the LSP ID is made up of: the 6-byte NLSP system ID, the local circuit number, and the lsp number. The number of entries in the packet is given.

NLSP.064

Level:
P-TRACE
Short Syntax:
NLSP.064 Snt PSNP: num= number_entries , IPX circuit ID nt PSNP: number_entries=%d, %S
Long Syntax:
NLSP.064 Snt PSNP: number_entries= number_entries , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A PSNP packet has been sent on the circuit. The number of entries in the packet is given.

NLSP.065

Level:
UI-ERROR
Short Syntax:
NLSP.065 Seq num wrap on LSP= LSP ID
Long Syntax:
NLSP.065 Sequence number wrapped on LSP= LSP ID
Description:
The sequence number has wrapped, or overflowed, on the Link State Packet for the given LSP ID. This should be an extremely rare occurrence. This LSP ID will be kept out of service and not regenerated for the maximum LSP age out period, which defaults to aproximately 2 hours.
Cause:
Unknown. The sequence number is a 4 byte unsigned number and should not be overflowing except in extrememly old, large NLSP networks. This is more likely due to router memory corruption or a software bug.
Action:
None, recovery should be automatic after the maximum LSP age out period.
Action:
If the router is to be restarted as part of the recovery action, the router should not be restarted for the LSP age out period.
Action:
As an emergency workaround, the router could be immediately restarted if the NLSP System ID is changed to another value on the problem router. By changing the NLSP System ID for the router, this changes all the LSP IDs generated by the router.

NLSP.066

Level:
UI-ERROR
Short Syntax:
NLSP.066 badIntCheckSum on LSP= LSP ID
Long Syntax:
NLSP.066 badInternalCheckSum on LSP= LSP ID
Description:
Corruption of routing information has been detected. The checksum on each Link State Packet (LSP) is periodicly reverified as a defensive measure to detect any possible memory corruption of the routing databases. The checksum for the LSP was relcalculated to be something different than the current value in memory. The routing database is automatically purged and reacquired, to recover from the situation.
Cause:
Possible software or hardware bug causing the memory corruption.
Action:
None, unless it occurs on a frequent basis. Recovery should be automatic.

NLSP.067

Level:
U-INFO
Short Syntax:
NLSP.067 WAN nbr system_id aged out: ht= hold_time , IPX circuit ID AN nbr %E aged out: holding time=%d, %S
Long Syntax:
NLSP.067 WAN nbr system_id aged out: holding time= hold_time , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A valid WAN hello packet has not been received from a neighbor within its holding time. The adjacency is moved to the down state.
Cause:
Neighboring NLSP router is no longer functioning on this circuit from an NLSP point of view.
Action:
If unexpected, investigate for possible crash, cable disconnect, etc. at the neighboring router.

NLSP.068

Level:
U-INFO
Short Syntax:
NLSP.068 RIP rt to ipx_net drp, not in area, IPX circuit ID IP rt to %X dropped, not in area, %S
Long Syntax:
NLSP.068 RIP rt to ipx_net dropped, not in area, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The routing information to the given IPX network is not used because it was not within the NLSP areas for the router. The RIP routing information was obtained from the given circuit.

NLSP.069

Level:
UI-ERROR
Short Syntax:
NLSP.069 LSU resource failure
Long Syntax:
NLSP.069 LSU resource failure
Description:
There was not enough memory resources to build our own LSU.

NLSP.070

Level:
UI-ERROR
Short Syntax:
NLSP.070 no buf for LANH, IPX circuit ID o buffer for LAN Hello, %S
Long Syntax:
NLSP.070 no buffer for LAN Hello, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
No packet buffer is available to send a LAN Hello packet.

NLSP.071

Level:
P-TRACE
Short Syntax:
NLSP.071 pkt frm source_net / source_node drp, IPX circuit ID acket from %X/%E dropped, %S
Long Syntax:
NLSP.071 Packet from source_net / source_node dropped, IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An NLSP packet has arrived on the given IPX circuit, but NLSP is either globally disabled, or disabled for this circuit. The packet is discarded.

NLSP.072

Level:
P-TRACE
Short Syntax:
NLSP.072 Rcv LSP: LSP ID sn= sequence_number rtim= remaining_time ck= checksum len= pkt_len IPX circuit ID ecived LSP: %E:%02X:%02X sequence_number=%X remaining_time=%d checksum=%X length=%d, %S
Long Syntax:
NLSP.072 Recived LSP: LSP ID sequence_number= sequence_number remaining_time= remaining_time checksum= checksum length= pkt_len , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
An LSP packet has been received on the circuit and is being processed. The LSP packet's 8-byte LSP ID, sequence number, remaining time, checksum and length fields are shown. The LSP ID is made up of: the 6-byte NLSP system ID, the local circuit number, and the lsp number. The length is the length of the NLSP packet, and does not include the 30-byte IPX header or the data link header.

NLSP.073

Level:
P-TRACE
Short Syntax:
NLSP.073 Rcv CSNP: start_sn= LSP ID , end_sn= LSP ID , num= number_entries , IPX circuit ID eceived CSNP: start_sn=%E:%02X:%02X, end_sn=%E:%02X:%02X, number_entries=%d, %S
Long Syntax:
NLSP.073 Received CSNP: start_sn= LSP ID , end_sn= LSP ID , number_entries= number_entries , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A CSNP packet has been received on the circuit. The starting and ending LSPIDs are shown; the LSP ID is made up of: the 6-byte NLSP system ID, the local circuit number, and the lsp number. The number of entries in the packet is given.

NLSP.074

Level:
P-TRACE
Short Syntax:
NLSP.074 Rcv PSNP: num= number_entries , IPX circuit ID eceived PSNP: number_entries=%d, %S
Long Syntax:
NLSP.074 Received PSNP: number_entries= number_entries , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A PSNP packet has been received on the circuit. The number of entries in the packet is given.

NLSP.075

Level:
P-TRACE
Short Syntax:
NLSP.075 NLSP Tree: paths_added= paths_added , nodes_placed= nodes_placed, , links_examined= links_examined
Long Syntax:
NLSP.075 NLSP Tree: paths_added= paths_added , nodes_placed= nodes_placed, , links_examined= links_examined
Description:
The NLSP tree has been recreated by the Decicsion process. The number paths found is given.

NLSP.076

Level:
P-TRACE
Short Syntax:
NLSP.076 XR Leaf upd= xroutes
Long Syntax:
NLSP.076 XR Leaf update= xroutes
Description:
The decision process has updated the forwarding database with the specified number of routes from External Route options from the Link State Database. The Leaf update does not require the NLSP tree to be rebuilt if only the leaf information has changed.

NLSP.077

Level:
P-TRACE
Short Syntax:
NLSP.077 Quick Leaf update: xrts= xroutes , serv= services
Long Syntax:
NLSP.077 Quick Leaf update: xroutes= xroutes , services= services
Description:
The decision process has updated the forwarding database with the specified number of xroutes and services. This operation is called quick because has been done by only changing the directly involved leaves of the tree.

NLSP.078

Level:
UI-ERROR
Short Syntax:
NLSP.078 bad len ind from src_ipx_node , pkt= packet_type , IPX circuit ID ad length indicator from %E, packet type=%s, %S
Long Syntax:
NLSP.078 bad length indicator from src_ipx_node , packet type= packet_type , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains the incorrect length for the length indicator field. The packet is discarded. The packet type is one of LANH, WANH, LSP, CNSP, or PNSP. The sender's IPX node number is given.

NLSP.079

Level:
UI-ERROR
Short Syntax:
NLSP.079 not ipx type 0 from src_ipx_node , IPX circuit ID ot ipx type 0 from %E, %S
Long Syntax:
NLSP.079 not ipx type 0 from src_ipx_node , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
A received NLSP packet contains an IPX packet type that is not 0. The packet is discarded. The packet type is one of LANH, WANH, LSP, CNSP, or PNSP. The sender's IPX node number is given.

NLSP.080

Level:
UI-ERROR
Short Syntax:
NLSP.080 areaMismatch from NLSP circuit ID , IPX circuit ID reaMismatch from %E:%02X, %S
Long Syntax:
NLSP.080 areaMismatch from NLSP circuit ID , IPX circuit ID īzlīzkčīzlhīzkøīzl(īzlXīzlīzlHīzl8
Description:
The received WAN Hello packet contains no area address that matches any of our area addresses. The packet is discarded.
Cause:
Possible misconfiguration of area addresses.
Action:
Adjust configuration of the area addresses.

NLSP.081

Level:
P-TRACE
Short Syntax:
NLSP.081 SI Leaf upd= services
Long Syntax:
NLSP.081 SI Leaf update= services
Description:
The decision process has updated the forwarding database with the specified number of services from Service Information options in the Link State Database. The Leaf update does not require the NLSP tree to be rebuilt if only the leaf information has changed.